Intertek Directory of Building Products

McKEON FireFighter® Model D200 and D200E 3 Hour Fire & Smoke Barrier Company: McKEON Code Compliance Research Reports: CCRR-0455

McKEON FireFighter^® Model D200 and D200E Curtain Assemblies are for use as fire and smoke barrier curtain assemblies when installed in a 3-hour steel stud/gypsum, gypsum-protected CLT (see limitations below), or masonry wall. Model D200 assemblies may contain curtain overlaps. Model D200E assemblies may contain overlaps and/or passage doors sealed with a hook & loop fastener. See below for ratings and limitations.

FIRE RATINGS

Test Standard	Rating
UL 10D	180 minutes
UL 10B, UL 10C, NFPA 252	20 minutes without hose stream

AIR LEAKAGE RATINGS

Test Standard	Test Type	Rating^a
UL 1784	Ambient Temperature	≤3.0 cfm/ft² at up to 0.10 in. of w.c.
UL 1784	Elevated Temperature	≤3.0 cfm/ft² at up to 0.10 in. of w.c.

^aThis assembly was evaluated without the use of an artificial bottom seal and may be installed in areas where pressurization is provided to control smoke movement in accordance with Section 4.3.2 of NFPA 105 and for hoistway opening protection and lobby doorways as allowed in Chapter 30 of the IBC.

CODE COMPLIANCE RESEARCH REPORT

Evaluation Method	Building Code	CCRR Number
UL 10B UL 10C UL 10D UL 1784	2024, 2021, 2018 IBC 2024, 2021, 2018 IFC 2023, 2020 FBC 2025, 2022 CBC 2023 LABC 2024, 2021, 2018 NFPA 101	CCRR-0455

MAXIMUM SIZE LIMITATIONS

Certification Procedure	Maximum Area	Maximum Width	Maximum Height
LABEL (with overlap)	93.44 sq ft	9'-8"	9'-8"
LABEL (without overlap)	143 sq ft	13'-0"	11'-0"
CERTIFICATE/LABEL	unlimited*	unlimited*	unlimited*

*Assemblies exceeding these dimensions must have an oversize label, issued by Intertek, stating the assembly is constructed in accordance with the certified design except for size. Acceptance of the oversize assembly is at the discretion of the Authority Having Jurisdiction.

MINIMUM SIZE LIMITATIONS (UL 1784 ONLY)^a

Clear Opening Width^b	Clear Opening Height^c
29.5"	78"

^aFire-only assemblies do not have a minimum size.
^bTip-to-tip width between side guides
^cDrop height below headbox

INSTALLATION LIMITATIONS
Assemblies may be installed in gypsum with structural steel stud, masonry, or gypsum-protected Cross Laminated Timber (CLT) walls. When installed in gypsum-protected CLT walls, the following conditions apply:

Supporting CLT wall must be fire-resistance-rated in accordance with the code.
Noncombustible protection shall be in accordance with the code, but not less than:
- Two layers of 5/8-inch Type X gypsum per face for walls required to have a fire-resistance rating of 2 hours or less.
- Three layers of 5/8-inch Type X gypsum per face for walls required to have a fire-resistance rating of 3 hours or more.
Assemblies bearing a fire-protection rating of 90 minutes or less shall be designed with an additional sacrificial 1 inch of anchorage embedment depth or be through-bolted.
Assemblies bearing a fire-protection rating of 2 or 3 hours shall use through-bolted anchorage.

Minimum Curtain Overlap (when present): 23-5/8"
Minimum Bottom Bar weight: 0.30 lbs per sq. ft. of curtain area
Maximum Curtain Rivet spacing: 15" on-center
Maximum Hook & Loop length: 8' 0"
Stainless Steel Hook & Loop required for fire applications
Side Guide anchorage: 1/4" anchors spaced maximum 18" on-center
Top Hood/Assembly mounting: maximum 40" on-center

Listing Report Certificate of Compliance Return to Search

Attributes

Certificate Date of Expiry	December 31, 2026
Certificate Date of Initial Registration	March 21, 2016
Certificate Number	WHI16–20384301
Criteria	UL 10(b) (2008) (R2009)
Criteria	UL 1784 (2015)
Criteria	UL 10(c) (2016)
Criteria	NFPA 252 (2017)
Criteria	UL 10(d) (2017) Ed.2
CSI Code	08 30 00 Specialty Doors and Frames
Listing Section	SMOKE CONTROL DOOR ASSEMBLIES
Spec ID	29655

Design Documents

No Results

Code Compliance Research Reports

CCRR-0455

Public Documents

No Results

Warnock Hersey Mark

Intertek ETL Mark

ETL Listed Mark